Pilot Rock RJ Thomas Mfg. Co.

WXT and WXTH Accessible Picnic Table - Using Aluminum

Please make the following configuration choices:

Standard Height Or Raised Top Table

Choose if you want the standard height table top or a raised top for additional wheelchair clearance under the top.

($59.00)
($41.00)

Frame Finish

Select the finish you want on the frames.

MATERIAL & LENGTH CHOICES

Select the Material and Length you want for this product.

($749.00)
($901.00)
($1,161.00)
($1,312.00)
($749.00)
($901.00)
($1,161.00)
($1,312.00)

Model WXT and WXTH Picnic Tables are ADA Compliant and accessible to wheelchairs at both ends.  These tables are designed and constructed specifically for heavy use areas where unusually difficult service may be required.  Now, EVERY picnic table in your facility can be fully accessible!

Specifications:

Model WXT and WXTH Picnic Tables utilize a patented innovative frame design.  They are ADA COMPLIANT and accessible to wheelchairs at both ends—they meet or exceed current ADA guidelines for wheelchair access to picnic tables.  Full length seats offer full capacity seating which is an advantage over extended top or side access tables.  The unique frame design includes two wheelchair spaces plus provides proper support under the outside ends of the full length seats.

The exclusive patented transverse frame leg under the seat makes this a very stable table.  The portable design gives you placement flexibility.

The WXT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe).  Nominal seat height is 18”.

The WXTH Series offers clearances under the table top of 30” wide, 31” high and 24” total knee and toe clearance (19” knee and 5” toe).  Nominal seat height is 19”.  The raised table top allows most wheelchair armrests to fit under it for a closer approach which is an advantage for some persons in wheelchairs and persons with certain physical restrictions.

FRAME: All welded 2-3/8” OD steel pipe (2.375 OD, 11 ga. Wall, 2” ID nom. pipe specifications).  Top/seat mounting brackets are 2” x 2” x 10 ga. die-formed steel.  Frames supported by diagonal braces of 1-5/16” OD steel pipe attached to center channel.   Frames are welded into a single piece structure for strength and easy assembly.   All 3/8” dia. Galvanized carriage bolt fasteners.  Warranted for Life.

FINISH: Standard finish: hot dip galvanized after fabrication.  Or choose a powder coat finish (in place of galvanized finish) in your choice of color. 

LENGTH: 6, 8, 10 or 12 ft. long.

TOP/SEAT MATERIAL: 2” X 10” (nom.) aluminum planks, top is pre-assembled at the factory.  Note:  The 6 ft table has nominally shorter seats.  Aluminum is available with clear anodized finish or in your color choice of powder coat paint finish.  See Material Options.

OPTIONAL: To anchor table to a concrete surface, use Model ANC6-4 Anchor Kit (Concrete Screws) and Model ANG-3 Anchor Kit (Anchor Straps).


 

You May Also Like

Charcoal Grills
Accessible Charcoal Grill - ASW and ASWS Series
Accessible Charcoal Grill - ASW and ASWS Series
SKW: ASW::
These charcoal grills meet the ADA guidelines for accessibility and operability. CLICK TO SEE MORE.
Trash & Recycling Receptacles
Round Receptacle - Side Door, Steel Strap
Round Receptacle - Side Door, Steel Strap
SKW: CN-R/SS2
The side door provides easy access to the liner inside.
Utility Tables
Utility Table - ULT Series
Utility Table - ULT Series
SKW: ULT
Simple design of these tables makes them convenient, easy to use and keep clean. CLICK TO SEE MORE.
Website design and development by Spindustry Digital, Des Moines, Iowa